您的位置: 标准下载 » 协会标准 » SAE 美国机动车工程师学会 »

SAE AIR1390 Convenient Location of Oxygen Masks for Both the Crew and Passengers of Aircraft

作者:标准资料网 时间:2024-05-14 07:57:28  浏览:9590   来源:标准资料网
下载地址: 点击此处下载
Product Code:SAE AIR1390
Title:Convenient Location of Oxygen Masks for Both the Crew and Passengers of Aircraft
Issuing Committee:A-10 Aircraft Oxygen Equipment Committee
Scope:There are four basic conditions requiring the dispensing of oxygen through oxygen masks to aircraft occupants in turbine powered aircraft during flight.The following conditions are derived from the Federal Aviation Regulations (FAR) as listed in Section 2.Condition 1: When the mission of the pressurized aircraft or the operational flight capability is in excess of flight level 300...All cabin occupants must be serviced by an automatic oxygen mask presentation system connected to an operational oxygen source which is activated automatically and/or oxygen flow initiated by the occupant displacing the actuating mechanism when pulling and placing the mask in position on his face in the event of an emergency pressurization failure. An additional 10% of oxygen masks and outlets are to be provided, uniformly distributed throughout the cabin of the aircraft.Condition 2: When the mission of the pressurized aircraft or the operational altitude of the aircraft is not in excess of flight level 300, but above flight level 250...Oxygen masks which are stowed connected to an oxygen supply and can be obtained immediately by each cabin occupant wherever seated when the aircraft is operating above flight level 250, must be available in the event of an emergency p deck crew member. Observers must have emergency oxygen, either passenger or crew type.Condition 2: When the mission of the pressurized aircraft or the operational altitude of the aircraft is not in excess of flight level 300, but above flight level 250...Oxygen masks which are stowed connected to an oxygen supply and can be obtained immediately by each cabin occupant wherever seated when the aircraft is operating above flight level 250, must be available in the event of an emergency pressurization failure.Condition 3: When the mission of the pressurized aircraft or the operational altitude of the aircraft is between 10,000 feet and flight level 250...Oxygen masks, which have been distributed or are stowed and are readily accessible to each ressurization failure.Condition 3: When the mission of the pressurized aircraft or the operational altitude of the aircraft is between 10,000 feet and flight level 250...Oxygen masks, which have been distributed or are stowed and are readily accessible to each cabin occupant when the aircraft is operating above 10,000 feet, must be available in the event of an emergency pressurization failure.Condition 4: When the mission of a non-pressurized aircraft is operating above 12,500 feet...Oxygen masks which can be connected to an operational oxygen source must be available and distributable to all occupants of the aircraft during such flight operations.Certain Federal Aviation Regulations (FAR's) cover the functional characteristics and requirements of the oxygen systems for aircraft in the mission and operational categories defined above. These should be referred to for the exact functional performance requirements. It is not the intent of this document to insure conformance with these regulations, but only to recommend general concepts for the location of the oxygen masks and oxygen system outlets for proper accessibility by the aircraft occupants, whether cabin ocegulations (FAR's) cover the functional characteristics and requirements of the oxygen systems for aircraft in the mission and operational categories defined above. These should be referred to for the exact functional performance requirements.
下载地址: 点击此处下载
【英文标准名称】:Plainbearings;Testingofthetribologicalbehaviourofbearingmaterials;Part1:Testingofthefrictionandwearbehaviourofbearingmaterial/matingmaterial/oilcombinationsunderconditionsofboundarylubrication
【原文标准名称】:滑动轴承.轴承材料摩擦特性试验.第1部分:界面润滑情况下轴承材料/配套材料/润滑油组合的摩擦和磨损性状试验
【标准号】:ISO7148-1-1985
【标准状态】:作废
【国别】:国际
【发布日期】:1985-03
【实施或试行日期】:
【发布单位】:国际标准化组织(ISO)
【起草单位】:ISO/TC123
【标准类型】:()
【标准水平】:()
【中文主题词】:摩擦;试验结果;滑动轴承;协同因素;摩擦学;润滑;磨损;摩擦试验;轴承;材料;试验;定义
【英文主题词】:tribology;wear;tests;testresults;definitions;bearings;plainbearings;testing;materials;lubrication;coefficients;friction;frictiontests
【摘要】:
【中国标准分类号】:J12;A42
【国际标准分类号】:3460
【页数】:6P;A4
【正文语种】:英语


Product Code:SAE AMS2350
Title:Standards and Test Methods (Cancelled Oct 1989)
Issuing Committee:Ams B Finishes Processes And Fluids Committee
Scope:To establish the issue of specifications, standards, and recommended practices published by standardizing agencies other than divisions and committees of the Aerospace Council of SAE approved for use in determining conformance to requirements of Aerospace Material Specifications (AMS) and other specifications in which this specification is referenced.